← Satin Celadon Glaze Recipe, ∆10Reduction
Effects of Reduction andOxidation →
Nuka Glaze Recipe, ∆10reduction
Posted on July 27, 2010 by shyrabbit
- Custer Feldspar 36.00
- Quartz 30.00
- Whiting 22.00
- OM-4 6.00
- Wood Ash (unwashed) 3.00
- Talc 2.00
- Bone Ash 2.00
Notes: This a ∆10 Reduction glaze that will fire to a Creamy White with low gloss to satiny finish. Good over tenmoku, will run if applied too thick over thick tenmoku. As always, test for your ingredient and firing conditions.
This entry was posted in Glazes and Techniques. Bookmark the permalink.
← Satin Celadon Glaze Recipe, ∆10Reduction
Effects of Reduction andOxidation →
18 Responses to Nuka Glaze Recipe, ∆10reduction
Dee Kat says:
July 27, 2010 at 5:19 pm
This just make me want to weep in envy. I so miss high reduction firing. I really don’t care what they say about how great midfire electric can be – it never can do this.
Reply
shyrabbit says:
July 28, 2010 at 3:23 pm
Dee Kat,
I understand and I know how fortunate I am to be firing ∆10. For me the variations, and degree of chance is what keeps me moving forward. Thanks, MichaelReply
Dee Kat says:
July 27, 2010 at 5:21 pm
(but then of course the pieces themselves are the perfect form for the glaze) – sigh again.
Reply
shyrabbit says:
July 28, 2010 at 3:24 pm
Dee Kat,
Thanks for the kind words, I really appreciate it.
MichaelReply
Joel Cherrico says:
July 28, 2010 at 2:34 pm
Great surface, thanks for sharing the recipe so I do some experimenting! Did the red tones at the lip come from dipping the pots in Temmoku first? Was Temmoku just glazed at the lip or over the entire pot? I’ve been trying to get similar colors on the rims of my pots using Red Iron Oxide stain…
Reply
shyrabbit says:
July 28, 2010 at 3:29 pm
Joel,
The pieces were first glazed overall with the tenmoku and then the nuka. The reddish lips on the pieces is due to the slight downward movement of the tenmoku when firing, causing the the glaze to “break” off the edges and textures. Hope this answers your question. Let me know if not.
MichaelReply
Terry says:
October 17, 2010 at 9:23 pm
Beautiful – both the glaze and the forms! Thanks for sharing the recipe. It will be at least 6 – 9 months before I get my studio up and running. Planning to stay with ∆10 reduction firing and love tenmoku combined with another glaze — so will file away for future use!
Reply
Teresa Gagne says:
January 12, 2011 at 8:07 pm
Thanks Michael. Beautiful forms and glazing. Could you share the tenmoku glaze recipe. I have the opportunity to fire in a friend’s gas kiln but only have a cone 9 tenmoku recipe.
Reply
Marcos Lewis says:
July 25, 2011 at 1:50 am
Is the wood ash a sub for rice hull ash?
Reply
Anonymous says:
July 25, 2011 at 2:44 am
Hi Marcos, Yeah the wood ash and the increased silica content of this glaze subs for the traditional rice hull ash.
MichaelReply
Maria Carmen says:
January 1, 2012 at 1:08 am
Thanks D.Michael for the recipes of nuka,,My name is Maria Carmen and I was looking for white nuka glazes for long time, do you know the book or where I can get the recipes for this glazes? I will be very grateful for that
My email is : hap.pi@live.com.au.
Thanks for your time
Regards
CarmenReply
shyrabbit says:
January 5, 2012 at 8:49 pm
Maria,
You’re Welcome. I’m not sure where I got this nuka glaze…It might be from Phil Rogers’ book titled “Ash Glazes”Reply
Maria Carmen says:
January 10, 2012 at 9:22 am
Michael thank you for the information, I’m looking for the book.
Michael I never use Rio, and I don’t know what it is, or any substitute of this. sorry I’m very ignorant still in pottery.
Thanks for you valuable time.
Regards
M.CarmenReply
Jay trrenchard says:
February 1, 2012 at 4:30 am
The nuka glaze recipe is in a book called Hamada Potter published about twenty years ago.. I used to be able to buy rice hull ash at an auto parts store as ” clean sweep” sweeping compound.. It works great in a Nuka glaze.. The basic glaze is equal parts feldspar, wood ash and rice hull ash. Rice hull ash is about 90 plus percent silica.
Reply
Hollis Engley says:
February 23, 2012 at 10:02 pm
That’s a great tip, Jay. I hadn’t heard that, though I think I have the Hamada Potter book. And the Phil Rogers book. I’ve just started using this recipe here at my studio and I love it.
Reply
Pingback: Speaking of Nuka | Dreams of Earth
Anonymous says:
July 7, 2016 at 12:37 am
Maria, RIO is red iron oxide
Reply
joanlizscott says:
October 21, 2019 at 2:33 am
Alberta slip mixture? Is it 100 percent Alberta? And how is it applied? Any advice is appreciated.
Reply